Shipping rates and destinations

WARNING  - THIS ACCESSORY IS NOT MEANT TO BE USED UNDERWATER AS PER MANUFACTURER INSTRUCTIONS! ANY ATTEMPT TO DO SO CAN CAUSE EQUIPMENT LOSS AND IS NOT COVERED BY THE WARRANTY!

Compatible models of underwater camera housings:

• Sony A6xxx series Salted Line 60M/195FT Underwater camera housing
• Sony RX1xx series Salted Line 60M/195FT Underwater camera housing
  
• Sony A7S III series Salted Line 60M/195FT Underwater camera housing
• Sony A7 IV series Salted Line 60M/195FT Underwater camera housing
• Sony A6600 40M/130FT Underwater camera housing
• Sony A6700 40M/130FT Underwater camera housing
  
• SeaFrogs Underwater camera housing for Sony ZV-E10 collection
• SeaFrogs Underwater camera housing for Sony ZV-E1 collection
• Sony A1 40M/130FT Underwater camera housing
• Sony A7C 40M/130FT Underwater camera housing
• SeaFrogs Underwater camera housing for Sony A7C II/A7CR collection
• Sony A7 II NG Series 40M/130FT Underwater camera housing
• Sony A7 III 40M/130FT Underwater camera housing
• Sony A7R III 40M/130FT Underwater camera housing
• Sony A7S III 40M/130FT Waterproof camera housing
  
• Sony A7 IV 40M/130FT Waterproof camera housing
• Sony A7R IV 40M/130FT Waterproof camera housing
• Sony A7R V 40M/130FT Waterproof camera housing
• Sony A9 40M/130FT Underwater camera housing
  
• Sony A9 II 40M/130FT Underwater camera housing
• Sony FX3 40M/130FT Underwater camera housing
• Sony FX30 40M/130FT Underwater camera housing
• Sony A7 IV NG 40M/130FT Underwater camera housing
• Panasonic Lumix GH5 & GH5 S 40m/130ft Underwater Camera Housing
• Olympus TG-5 & TG-6 60m/195ft SeaFrogs Underwater Camera Housing
• SeaFrogs Underwater camera housing for Fujifilm X-H2 collection
• Fujifilm X-T5 40M/130FT Underwater camera housing
• Fujifilm X-T4 40M/130FT Underwater camera housing
• Fujifilm X-T3 40M/130FT Underwater camera housing
• Fujifilm X-S20 40M/130FT Underwater camera housing
• Canon EOS M50 40m/130ft SeaFrogs Underwater Camera Housing
• Canon EOS M6 Mark II Waterproof camera housing
• Canon EOS R5 Waterproof camera housing
• Canon EOS R6 Waterproof camera housing
• SeaFrogs Underwater camera housing for Canon EOS R6 II collection

Included

• Electronic valve
• Pump
• Screwdriver (for battery replacement)
  
  

The vacuum pump system is used for checking the water tightness of underwater camera housing before submerging.

Install the camera inside underwater camera housing in a dry and low humidity level place.

15-30 minutes before your dive remove the lid from the backplate to access the vacuum pump system opening (Illustration 1) and make sure the O-ring stays in place. Attach a vacuum pump system to the opening by screwing it clockwise (Illustration 2). Unscrew the lid of the electronic valve (Illustration 3) and press the button to turn on the LED inside the valve (Illustration 4). Attach the rubber part of a pump to the valve and start pumping air out (Illustration 5). Red LED starts blinking, indicating ambient atmospheric pressure. The hand pump is fitted to the threaded valve body and the air is pumped out of a unit until the red LED changes to green LED and add couple more strokes to make sure the sufficient underpressure. The additional stroke or two ensures that the valve is not on the edge of the threshold. The pump is then removed, and the protective cap is replaced to ensure airtightness. Observe the green LED blinking for 15 minutes to make sure there is no air leakage. Unscrew the lid of a valve to access the button and press it for a few seconds to release the pressure from inside and turn the valve LED off (Illustration 4). Remove the valve from the backplate and place the vacuum opening lid in its original place, make sure the O-ring is still there (Illustration 1). - safe to dive!